Pelican 1535 Air Case wheeled w. TrekPak-Foam Hybrid System

Pelican 1535 Air Case wheeled w. TrekPak-Foam Hybrid System

Pelican 1535 Air Case wheeled w. TrekPak-Foam Hybrid System

Loading product options

Combining strength and lightness, the Pelican 1535AirTPF Wheeled Carry-On Air Case with TrekPak Dividers and Pick-n-Pluck Foam in black is watertight, crushproof, dustproof, and optimized for travel. For travel by air, Pelican has aggregated available airline rules for maximum overhead and check-in dimensions with the goal of creating a case that conforms to their requirements. Of course, there will always be exceptions, so it's wise to contact your carrier before departing.

Your 1535AirTPF case is made of a super-light, proprietary HPX polymer (with honeycomb structural elements) that is up to 40% lighter than most other Pelican polymers. This confidence-inspiring design has been drop-tested on concrete on all sides and corners while loaded with gear. The case is also tested with a 28-pound steel dart dropped from a height of three feet, submerged for 30 minutes at a depth of 3.3 feet, and the wheels are roll tested over 1000 yards with loads at 5 mph.

The case has ABS double-throw latches that accept a user-supplied padlock, a watertight O-ring gasket, an automatic purge valve, and stainless steel hasp protectors. Users will appreciate the conic-curved lid shape, the rubber overmolded handles, and the extending trolley handle. For easy case identification, a removable polycarbonate cardholder may be placed on the front or side of the case.

Besides being lighter than traditional padded dividers, the TrekPak Divider System uses preinstalled wall sections, divider panels, locking pins, and an easy-to-use cutting tool. Simply lay your gear in the case, measure and cut the divider sections, and lock them in place with the steel U-pins. Extra divider material is included for occasions where your equipment requirements vary. The 7/16" thick divider sections are made of waterproof, closed-cell foam that is laminated to a rigid, corrugated plastic panel to resist tearing and shredding. The TrekPak is combined with a 1" top and bottom foam to give your gear 360-degree protection. This TrekPak/Foam Hybrid configuration combines the benefits of TrekPak dividers with a Pick-n-Pluck foam section.

Note: Product is shown in use for illustration Only, additional equipment is not included.

 

  • MPN - 1535AIRBTPF
  • GTIN - 019428170455
Material Body: HPX Polypropylene Blend Polymer
Latch: ABS
O-Ring: EPDM
Purge Body: ABS
Purge Vent: Hi-Flow Gore-Tex 3-Micron Hydrophobic Non-Woven
Purge O-Ring: 70 Shore Nitrile
Waterproofing Watertight O-Ring Gasket
Maximum Buoyancy Floats in Salt Water with 64.8 lb / 29.4 kg
Temperature Range 0 - 140°F / -18 - 60°C
Type of Closure Hinged with Double ABS Latches
Interior Fitting TrekPack/Foam Hybrid
Carrying/Transport Options Overmolded Handle, Extending Trolley Handle, and Wheels
Volume 7.1 gal / 26.9 L
Interior Dimensions Overall: 20.39 x 11.2 x 7.21" / 59 x 28 x 18 cm
Bottom Depth: 5.21" / 13.2 cm
Lid Depth: 2" / 5.1 cm
Exterior Dimensions 21.96 x 13.97 x 8.98" / 55.8 x 35.5 x 22.8 cm
Weight 9.98 lb / 4.53 kg
  • Watertight, Dust, and Crushproof Case
  • Made of Super-Light Polymer
  • TrekPak/Foam Hybrid
  • ABS Double-Throw Latches
  • Watertight O-Ring Gasket
  • Built-In Purge Valve
  • Stainless Steel Hasp Protectors
  • Conic-Curved Lid Shape & Wheels
  • Overmolded Handles & Trolley Handle
  • Polycarbonate Card Holder